Drain master B & BS

Air leakage is so little that economic effect is excellent,
and withdrawal of early investment expense is fast.

Outlet diameter is large (inside diameter 12Ø) that
there is no block phenomenon, and it is safety
because there is restoration ability when converts to
emergency mode.

Control is easy because all operations are automated.
It operates normally in atmospheric pressure state.
Emergency manual operation is available .
(needs not by-pass line)

Body:SCS13A,
Ball:Durability is good and strong against
corrosion by using SUS304 quality of the material.

Switching time of electric actuation ball valve is
short that operate ball valve is opened perfectly
at operation.(scale discharge is excellent)

dmb-001
dmb_동작원리01
dmb_동작원리02

DRAIN MASTER B Operation Principle

1)  Condensate that is flowed through lead-in line 1 is gathered to housing 2

2)  If condensate water level rises in housing, it is sensed in the high level sensor 3.

3)   Electric actuation ball valve 5 is run if transmit open signal in main board and condensate is
discharged through outlet 6

4)   If level of condensate water inside housing comes down 4 it is sensed in the sensor bottom
dead center, and electric actuation 6 ball valve that received close signal is closed.

dm-1500b

DM-150B

dm-500b

DM-500B

dm-150b

DM-1500B

Electrostatic Capacity Sensor

Any condensate from compression process can be sensed
correctly and discharged.

Zero loss of compressed air.

Uses of two sensors (High level, low level) protects energy loss
By air loss discharging condensate selectively.

dmb-pr1
dms_정상모드
Normal Mode
dms_비상모드
Alarm Mode
모드3
Counting Module

Automatic discharge function[Alarm]

In case of condensate in not discharged while 2 min. by scale etc.,
It makes recognition to user through alarm signal and it is converted
to automatic restoration function and it activates electric motion
ball valve by 5 sec. every 3min. It is returned by normal mode if
discharge is activated normally.

Durability [Hard-Anodizing]

Housing coated rigid coating applying for aircraft, semiconductor
Equipment etc. of industrial equipment required durability is excellent
nature of rust proof durability and abrasion etc. so that life of housing is
Semi-permanent.

Various model, beautiful design

Extended user’s selection by subdividing into three models according
to quantity of condensate, and housing is processed by anodizing method
and die casting mold that has beautiful design

dmb_stainless_01
Stainless Steel
dmb_설치및유지01

Convenience of install and maintenance

Put lead-in line more than 2 lines so that power connection is easy
and piping is convenient

Housing internal pollutant cleaning is simple

The built-in strainer can prevent blockage of valve by sludge

DRAINMASTER BS

ba03

Stainless Steel DM-150BS


DRAIN MASTER® Series Heating system

Automatic temp controller (heating unit)(Heating Unit)

The automatic temp controller prevents freeze when the condensate drain trap is installed in frozen areas or during winter.

DRAIN MASTER® Series is equipped with a dedicated heater, preventing damage by a fire to products caused by freeze in advance.

The instructions provide how to install the heater for DRAIN MASTER® Series and product composition. Please follow the instructions provided herein so as to ensure proper operation of the product.

– Composition –

Use of stainless steel ensures high durability and corrosion resistance, and the automatic temp controller maintains constant temperatures.

Connection to the lead-in line of DRAIN MASTER® Series is done by the screw thread for easy installation. Series

It is applicable to any model of DRAIN MASTER® Series and also to the existing trap.

※ For freeze protection

heater002
Technical Data
Application Temp’ -25 ~50℃ Power 110, 220Vac(±10%) 50~60Hz
Weight 0.4kg Switching Temp’ On/+5 ~ Off/+15℃
Threaded Connection G1/2” Power Input Pac < 125W
Material (Heating Cartridge) Stainless Steel Cable Cross-section 3 X 0.75㎟
(Connecting Cable) PVC 220Vac/125W Order ref. : A DM 00-1
Operating Pressure(max) 60 bar 110Vac/125W Order ref. : A DM 00-2

INSTALLATION

DM – 5,15,50

INLET x 2 : Installation by inserting a gasket into the bottom inlet hole.

DM – 150, 150B, 500, 500B

INLET x 3 : Installation by inserting a bushing and gasket into the bottom inlet hole.

DM – 1500, 1500B

Exclusive line for the heater(1/2”) : Installation by inserting a gasket into the bottom inlet hole.

DIMENSION

INFORMATION –

1. Install according to the instructions and maintain rated voltage.

2. Provide a heating system to the condensate lead-in line.

3. Run the heating system in a frozen area or during winter.

4. Power installation should be done by qualified technicians.

※ Do not provide a heating system to our heater exclusively used for the trap.